12 volts 100 W DALI-2 & PUSH intelligent dimmable tension constante LED pilote alimentation LED lumières
Pilote LED à tension constante standard DT8 série DALI-2 100 W, conception à 4 canaux. Conforme au protocole de gradation DALI-2 IEC62386. Plage de gradation ultra profonde entre 0,1 et 100 %. Processus de gradation fluide sans scintillement, avec fonction de protection contre les courts-circuits/surchauffes/surcharges, conformément aux réglementations mondiales en matière d'éclairage de sécurité. 7 ans de garantie
spécification
| Modèle | SMT-JB12100V-DP2-4C | SMT-JB24100V-DP2-4C | SMT-JB36100V-DP2-4C | SMT-JB48100V-DP2-4C | |
| Sortir | Tension continue | 12 V (12-13,5 V) | 24 V (24-26 V) | 36 V (36-38 V) | 48 V (48-50 V) |
| Tolérance de tension | ±0,2V | ||||
| Courant nominal | 8.34A | 4.17A | 2,78A | 2,08A | |
| Puissance nominale | 100W | ||||
| Régulation de tension | 0,50% | ||||
| Régulation de charge | 2% | 1% | 1% | 1% | |
| Saisir | Plage de tension | 100-277 VCA | |||
| Gamme de fréquences | 47 - 63 Hz | ||||
| Facteur de puissance (Typ.) @ pleine charge | PF≥0,98 à 120 VCA PF≥0,95 à 277 VCA | ||||
| THD(Typ.)@ pleine charge | ≤10%@120VAC ; ≤15%@277VAC (pleine charge) | ||||
| Efficacité (Typ.) @ pleine charge | 88,5 % à 120 VAC 89,5 % à 277 VCA |
87,5 % à 120 VCA 89,5 % à 277 VCA |
88 % à 120 VAC 89,5 % à 277 VCA |
88 % à 120 VAC 89,5 % à 277 VCA |
|
| Courant alternatif (Max.) | 1,3A | ||||
| Consommation d'énergie à vide (facultatif) |
1,15 W (@120 V) 1,05 W (@277 V) |
1,00 W (@120 V) 0,95 W (@277 V) |
1.10W(@120V) 1.05W(@277V) |
1.17W(@120V) 1.10W(@277V) |
|
| Standby power Consumption(optional) |
0.20W(@120V) 0.47W(@277V) |
0.25W(@120V) 0.47W(@277V) |
0.20W(@120V) 0.48W(@277V) |
0.20W(@120V) 0.48W(@277V) |
|
| Inrush Current (Typ.) | 23.2A,360us@50%Ipeak@120VAC;54.0A,280us@50%Ipeak@277VAC | ||||
| Leakage current | <0.5mA | ||||
| Protection | Short Circuit | Hiccup mode, recover automatically after fault condition is removed | |||
| Over Load | ≤120% ,hiccup mode, recover automatically after fault condition is removed | ||||
| Over temperature | case temp. over 100℃±10℃,output will be off; recovers automatically after temp. drops. | ||||
| Environ-ment | Working TEMP. | -40 ~ +70℃ (see below derating curve) | |||
| Working Humidity | 20 ~ 90%RH,non-condensing | ||||
| Storage TEM.,Humidity | -40 ~ +80℃,10 ~ 95%RH | ||||
| TEMP.coefficient | ±0.03%/℃(0 ~ 50℃) | ||||
| Vibration | 10 ~ 500Hz, 2G 10min./1 cycle,period for 60min. each along X,Y,Z axes | ||||
| Safety & EMC | Safety standards | UL8750 UL1310 | |||
| Withstand voltage | I/P-O/P:1.88KVAC I/P-FG:1.88KVac O/P-FG:1.88KVac | ||||
| Isolation resistance | I/P-O/P:100MΩ/500VDC/25℃/70%RH | ||||
| EMC Emission | FCC Part15 Subpart B;ANSI C63.4:2014 | ||||
| EMC Immunity | EN61000-4-2,3,4,5,6,11 EN61547 | ||||
| Others | Net Weight | 0.83kg/pcs | |||
| Dimension | 241*125*40mm (L*W*H) | ||||
| packing | Qty: 20cs/ctn; G.W: 18kg/ctn; Ctn size:300*280*215mm | ||||
| Notes | 1. All parameters NOT specially mentioned are measured at 230VAC input , rated load and 25℃of ambient temperature. | ||||
| 2. Tolerance: includes set up tolerance, line regulation and load regulation . | |||||
 |
 |
 |
 |
Mechanical Specification
※Input & Output wiring
※Input electronic cable 3*18AWG, the green cable connect with (FG) ,Black with AC (L), White with AC(N) (US);
※Output : 12V electronic cable 3*16AWG to be connected to LED Light;
24V electronic cable 3*18AWG to be connected to LED Light;
※Dimming cable
※Dimming electronic cable 3*18AWG, Brown DA/N and Purple DA/L (No polar) connected to the DALI BUS when use DALI function.
Brown (N) is connected to AC (N) while Purple (L) and pink (CCT Push )connected to CCT Push dim switch dimmer( L) when use Push function.
※Please make sure you connect these correctly otherwise your product will not function correctly and could be damaged.
CCT (TW) dimming: electronic cable, Black is output ( V+) Positive, While (CW-) and Yellow (WW-) are output (V-) negative
Note: there is external antenna at output side. Don't disassemble!
Dimming Operation
※Note: For DALI Dimming Wiring Diagram 3, please noted that only one DALI power is need in the DALI bus, so no extra DALI power is needed if the Master or Dimmer already includes the DALI Power.
Dimming Operation
※The default address for the DALI-2 LED driver is 001.
※Address settings device:
※Address settings:
① RDM setting address:
Set the address by the RDM device. For detailed operation, please refer to RDM device instruction manual.
② NFC setting address:
The DALI-2 led drivers’ address can be read and written by a mobile with NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DALI-2 LED drivers.
■ Adjust output voltage Operation
※Adjust output voltage slightly for DALI-2 LED drivers
1) The driver output voltage can be read and written by a mobile with NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DALI-2 LED drivers.
2) Voltage range: level 1~10, each level is 0.2V. The default output voltage level is 1.
Rated Vol. |
Level 1 |
Level 2 |
Level 3 |
Level 4 |
Level 5 |
Level 6 |
Level 7 |
Level 8 |
Level 9 |
Level 10 |
12V |
12.00V |
12.16V |
12.32V |
12.48V |
12.64V |
12.80V |
12.96V |
13.12V |
13.28V |
13.50V |
24V |
24.00V |
24.22V |
24.44V |
24.66V |
24.88V |
25.1V |
25.32V |
25.54V |
25.66V |
26.00V |
36V |
36.00V |
36.22V |
36.44V |
36.66V |
36.88V |
37.10V |
37.32V |
37.54V |
37.66V |
38.00V |
48V |
48.00V |
48.44V |
48.44V |
48.66V |
48.88V |
49.10V |
49.32V |
49.54V |
49.66V |
50.0V |
Simple operation about DALI-2 LED driver address reset and adjusting output voltage slighting by a mobile with NFC APP (set NFC) or NFC handheld device (NFC read & write device: NFC-RW)
Ø Mobilephone NFC APP setting:
Related Products
100W DALI-2 & PUSH intelligent dimmable led driver Aluminum housing design, waterproof grade IP67, good heat dissipation, can provide stable protection for lamps. Suitable for outdoor intelligent led lighting project installation. With 7 years warranty Model: SMT-12100V-DP2-2C Input Voltage: 100-277VAC Dimming Mode: DALI Dimmable |
